Your primary responsibility is the safe operation of the vehicle. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. To adjust the shoulder belt height, pull on the center button and slide the height adjuster down. If the light remains on, have the system serviced immediately by your authorized dealer. It is recommended to tow your vehicle with all four 4 wheels off the ground such as when using a car-hauling trailer.
During this time the selected button indicator light will blink slowly. A 10°F 6°C temperature drop can cause a corresponding drop of 1 psi 7 kPa in inflation pressure. When weather temperature changes occur, tire inflation pressures also change. Move the switch to move the seat forward, backward, up or down. Reach behind the rear bumper to locate the bulb. Wipe the surface with a damp, clean, white cotton cloth.
Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford. For optional message center: 1. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed. When installing cleat, reverse instructions above. If the image is still not clear after cleaning, have your system inspected by your authorized dealer. Place the transmission in N Neutral.
Push seat cushion down until it locks into horizontal position. Note: In the illustration, the vehicle on the bottom is used to designate the assisting boosting battery. This must be accomplished within 10 seconds. The emission system heats up the engine compartment and exhaust system, which can start a fire. The customer warranty may be void for any damage to the engine if such spark plugs are not used. Your vehicle is not equipped with the Ford Ambulance Preparation Package. For all other vehicles which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.
In Canada, check with your local St. The indicator lamp is located in the center stack of the instrument panel just above the radio. Enter factory—set 5—digit entry code. Press this button again to return to the previous air flow selection. Additional owner information is given separate publications, this Owner's Guide describes every option model variant available, and therefore some of the items covered may not apply your, options before they generally available. If a specific category is selected, Jazz, Rock, News, etc.
Push up on the outside rigid edge of the filter until the tabs are released, then rotate the air filter toward the front of the vehicle. Note: The temporary tire size for your vehicle may be different from this example. Rotate clockwise to the second position to also turn on the headlamps. In the event the accelerator pedal becomes stuck or entrapped, applying steady and firm pressure to the brake pedal will both slow the vehicle and reduce engine power. Reinstall the lug nuts until the wheel is snug against the hub. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
For an overheating condition, let the system cool off, then turn the ignition key off then on. Use the up and down arrows to get to any of the optional features. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Connect the two panels, then rotate both knobs a quarter-turn clockwise to secure the panels. Pull the lever fully again to deactivate.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. They are committed to meeting your service needs and to assuring your continuing satisfaction. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. The safety belt pretensioner uses the same crash sensor system as the front airbags and Safety Canopy System. Open the latches to release the panels. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Ford is also allowed a final repair attempt in some states.
Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. Wiring diagrams are black and white, but they frequently have color codes printed on each line of the diagram that represents a wire. Place the transmission in N Neutral. Warmer settings are indicated by more indicator lights. Engine oil filler cap out of view 8. Generally this is when they reach a height of at least 4 feet 9 inches 1.
Carefully pull the lamp assembly straight rearward from the tailgate pillar to disengage two hidden snap-in retainers. Certain vehicle components contain or emit chemicals known, the State of California to cause cancer and birth defects other, certain products of component wear contain emit chemicals known, to the State of California to cause cancer and birth defects other. Steps for determining the correct load limit: 1. To operate the cooled seats: Press the cooled seat symbol to cycle through the various cooling. Information on transfer case operation and shifting procedures can be found in this chapter. Your primary responsibility is the safe operation of the vehicle. A memory seat position may be programmed at any time.