Check out our complete line of products. Maintaining the transmission in your Chevrolet car Chevy Chevrolet car as part of normal vehicle maintenance routine will help ensure a long and trouble-free driving life. Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Remove the remaining bolts and lower the pan. Built to last, your Chevy S-10 handles anything you throw at it. If no fluid runs out, check your manual for what transmission fluid to use. Clean the entire transmission pan with solvent and dry it with compressed air.
Connect a new gasket to the transmission pan--make sure the pan's surface is clean--then install the pan back onto the transmission, tightening each bolt a quarter turn at a time. Insert the funnel and add the 7 quarts of transmission fluid up to the full marker. If the pan it stuck to the transmission by the gasket, gently pry it loose with a screwdriver, being careful not to bend the pan's mounting surface. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Remove the dipstick from the dipstick tube and insert the transmission funnel in it's place.
When adding, be sure to fill to the appropriate level, as recommended in user manual for your Chevrolet S10 2003. If the transmission fluid level on your S10 is low, you need to add fluid through the dipstick tube. When it comes to your Chevrolet S10, you want parts and products from only trusted brands. The fill plug, drain plug are both on the back side of the transfer case facing the rear drive shaft. Open the hood and pull the transmission dipstick out of the transmission filler tube. The transmission should hold 7. Remove the bottom pan from the transmission to drain the transmission fluid out of your Chevrolet pick up trucks transmission, clean the pan out carefully, replace the transmission filter, Install the new gasket, and both the transmission pan back in place.
Shop online, find the best price on the right product, and have it shipped right to your door. Lower the pan from the transmission. Remove the pan by removing the remaining bolts and pour any remaining fluid into the drain pan. Slide the drain pan and your tools out from under the car. If you're not sure, ask your dealer. Remove the filter's seal from the transmission with a screwdriver if it didn't come off with the pan. If it is 2 wheel drive the front speed sensors are mounted to the spindle behind the rotor.
Automatic Transmission Raise the truck, support it on jack stands and place the drain pan under the transmission pan. Loosen the bolts on the rear by about four turns without removing them. Mar 15, 2011 This is in the owners manual pages 269 and 270. This is how it works. First confirm the level of fluid before filling it. But that's not the case on your vehicle.
I was lucky to get fire out before truck burnt to the ground. Fill the transmission case with fresh transmission fluid using a syringe bottle or hand pump--make sure this tool has never been used for any other task. Remove the dipstick from the dipstick tube and insert the transmission funnel in it's place. Unscrew and remove the mounting bolts on the side and the rear of the transmission pan. Remove the drain plug on the transmission, which is the lower of the two plugs and will likely require a hex wrench to remove.
Select a 10 mm socket, extension bar and ratchet from the socket set and place it near the drain pan under the car. If you have an automatic transmission, the fluid is added through the tube that holds the dip stick to check the fluid level. Changing break fluid in Chevrolet S10 2003 is also is a simple task. Just Commodores -Holden Commodore Discussion Forum. Remove the old gasket form the pan and clean the pan thoroughly with degreaser.
The use of these materials may affect transmission operation and result in damage to internal transmission components. Go through the list of help links below:-----its having complete step by step procedure. Use the flat-head screwdriver to remove the gasket. Do not use supplemental transmission fluid additives, treatments or cleaning agents. Lower the truck off the jack stands using the floor jack. Pour it in the hole on top where the red cap is until the fluid runs out - all while the car is running. Use the rubber mallet to gently tap on the pan to drain the fluid.
Install and tighten the fill plug securely. Locate the red transmission cap under the hood. Checking and adding manual transmission fluid if equipped 1. Gently pry the old rubber filter seal out of the transmission using a screwdriver. The fluid level should be between the upper and lower marks on the tip of the dipstick. If transmission fluid runs out, I believe the transfer case input shaft seal is shot and needs replaced.