Loosen intermediate muffler shield and 2. Adjust drive pinion and ring gear see page 39 - 125. Kukko, size 120°C and press as possible with a suitable piece pipe. The brake fluid for operating the transverse lock is obtained from the piston reservoir mounted on the high pressure pump. The spacer sleeve is no longer required thanks to the new needle-roller assembly. Adjust modulating pressure see page push aside as far as possible. Measure internal resistance of the solenoid valve.
If necessary, Bearing assembly pull out with press in with with drive pinion suitable puller locally made tool Note quantity Redetermine, Shim and thickness if necessary reinstallation Replace. Replace inner plates of reverse gear brake B 3; adjust play to smallest value. Unscrew hex bolt and remove Zl. Say, if you really want to do the librarian thing, here's a suggestion. Install split radial bearing on output shaft 10. I wanted to help you by telling you of another very important source of information.
Place all balls and valves in shift valve housing see layout drawing. The same car also competed in 1000k races at Spa, Brands Hatch and Silverstone in 1984, but with little success. Sever bowden cable behind threaded connector. Check modulating pressure, correcting if necessary 3. Push down on diaphragm spring with circlip until circlip engages in its groove. Tightening torque: 8 Nm 5.
Check whether kickdown switch sticks in pressed position, replacing if necessary. Porsche wanted to promote the performance of the 928 to North America. Place shims determined for pinion adjust- ment between transmission case and final drive case. The engine was enlarged to 4. Note: Hold seal on special tool with a small amount of grease and drive in seal that sealing lip faces automatic transmission.
Say, if you really want to do the librarian thing, here's a suggestion. Heat tapered roller bearing inner races to approx. Valve Body Pressure Test A pressure tester with up fo 25 bar pressure range This pressure test wll lndlcate any defects in the is required for measuring the operating pressure. This is probably a good moment to recap the different versions of the 928 and explain the choices available to me. However, if specified play cannot be reached with snap rings, the center outer plates must also be used for adjusting. Place leaf spring with holder position and tighten mounting bolts slightly do not tighten 63.
A different car should be used for comparison. I wanted to help you by telling you of another very important source of information. Pry off plug carefully with two screw 1. Circlip Spring plate Insert right way round Compression spring Piston Insert right way round Sealing ring Sealing must face Nith toward cover Sealing ring with iex bolt Tightening. In 1986, revised suspension settings, larger brakes with 4-piston callipers and modified exhaust system was available on the 928S, marking the final changes to old body style cars. Remove snap ring and lift inner plate carrier plate carrier. Read a few of these write-ups and tell us what you think.
In 2007, 2008 and 2009 American racing driver Carl Fausett took his specially prepared and supercharged 1978 Porsche 928 to the Pikes Peak International Hill Climb and competed in the Open Division. Support transmission on stabilizer with Special Tool 9164 if necessary, lift trans- mission on transmission support slightly. Compression change was done with different shape piston tops. . From 1987 through 1995, the front spoiler was integrated into the nose and the rear spoiler became a separated wing rather than an integrated piece, and side skirts were added.
Note: Hold seal on special tool with a small amount of grease and drive in seal that sealing lip faces automatic transmission. The Brumos team tinkered with the suspension set up to make the car more stable. Small corrections can be made by Note: tapping face of central shaft with plastic Replace entire central tube with shaft and hammer. Press out pinion with a piece of suitable pipe. Note: The outer seal on the rear transmission 3.
At the time, 928 values had reached their nadir. Seemingly simple question, however the answer was surprisingly more complex. Instructions Removing Installing Install with Piston Special Tools 9317 and 9318 Position correctlv. Tests - Bleed pressure gauge No. All Rights Reserved This entire site with its content is copyright or trademark protected. Keesings Auto Magazine in Flemish.